Order before 3pm, dispatched same day
Order before 3pm, dispatched same day Research Use Only
Pay by Card / Apple Pay
99% Purity Money Back Guarantee Retatrutide Now Available
Lab ReferencePeptide BasicsResearch Use Only

Laboratory Reconstitution Guide

Preparing research peptides for use

Research peptides are supplied lyophilised (freeze-dried) because it keeps them stable. Reconstitution means dissolving that powder in a sterile solvent — usually bacteriostatic water (BW), which contains 0.9% benzyl alcohol. Good sterile technique matters at every step. This guide covers laboratory preparation only, not human or animal use.

What this guide covers

  • Equipment checklist
  • Step-by-step reconstitution process
  • Interactive concentration calculators
  • Volume reference table for standard vial sizes
  • Troubleshooting dissolution, cloudiness and precipitation
  • Post-reconstitution storage

Before starting, you will need

  • Bacteriostatic water
  • 1 mL insulin syringes with fine needles
  • 70% isopropyl alcohol swabs
  • A clean work surface
  • The lyophilised peptide vial
  • Refrigerator access at 2–8°C
Compliance note: All Pure Grade Labs products are research chemicals for laboratory use only and are not for human use.

Equipment Checklist

Bacteriostatic Water

The standard solvent for reconstitution. Don't substitute plain sterile water, saline or tap water.

Insulin Syringes (1 mL)

Used to measure and transfer BW. Fine gauges (28–31G) are recommended — use a fresh syringe every time.

Alcohol Swabs (70% IPA)

For disinfecting vial septums and your work surface before you begin.

Clean Work Surface

A flat, non-porous surface wiped with 70% IPA, in an area with minimal air movement.

Refrigerator Access (2–8°C)

Have space ready in the fridge before you start reconstituting.

The Peptide Vial (Lyophilised)

Check the seal, label, lot number and quantity before use.

Step-by-Step Reconstitution Process

Follow these steps in order.

  1. 1

    Prepare your work surface

    Wipe the surface with fresh 70% IPA, let it air-dry completely, then lay out your equipment.

  2. 2

    Inspect the peptide vial

    Check the powder, septum and crimp seal. If the seal is compromised, don't proceed.

  3. 3

    Swab both vial septums

    Wipe each septum in one direction with a fresh swab, then let it air-dry for 15–20 seconds.

  4. 4

    Draw up bacteriostatic water

    Use a fresh insulin syringe and avoid air bubbles. Use more than one draw if needed, and confirm the volume before continuing.

  5. 5

    Add the water to the peptide vial

    Aim the water down the inside wall of the vial rather than directly onto the powder, and add it slowly.

  6. 6

    Swirl gently — do not shake

    Swirl for 15–30 seconds. The finished solution should be clear, with no visible particles.

Laboratory Reconstitution Calculator

Enter vial quantity and bacteriostatic water volume to calculate the resulting concentration per mL. This is the starting point for all subsequent calculations.

Calculator A

Enter vial quantity and water volume above to calculate concentration.

Concentration
0mcg/mL
Milligrams0 mg/mL
Per 0.1 mL0 mcg
Per unit0 mcg

Output = concentration per mL (mcg/mL and mg/mL). For laboratory reference only — not a dosing guide.

Volume Analysis Calculator

Using your vial details and the volume drawn into the syringe, calculate the exact quantity in that volume, in mcg and mg.

Calculator B

Enter all three values above to calculate quantity in drawn volume.

Quantity in drawn volume
0mcg
Milligrams0 mg
U-100 units0 units
Concentration0 mcg/mL
The drawn volume is more than the water added to the vial.
Tip: On a U-100 insulin syringe, each unit mark = 0.01 mL. So 10 units = 0.10 mL, and 25 units = 0.25 mL.

Output = quantity in the drawn volume (mcg and mg). For laboratory reference only — not a dosing guide.

Volume Planning Calculator

Enter a target quantity in mcg or mg — the other field fills in automatically. Then add your vial details to calculate the volume to draw.

Calculator C

Enter target quantity and vial details above to calculate draw volume.

Volume to draw
0mL
U-100 units0 units
Concentration0 mcg/mL
Target0 mcg
This is more than a 1 mL (100 unit) syringe holds.

Output = volume to draw (mL) and equivalent U-100 insulin syringe units. For laboratory reference only — not a dosing guide.

Common Volume Reference Table

Standard combinations for planning reference only.

Vial SizeBW AddedConcentration Per mL
2 mg1 mL2,000 mcg/mL
2 mg2 mL1,000 mcg/mL
5 mg1 mL5,000 mcg/mL
5 mg2 mL2,500 mcg/mL
10 mg1 mL10,000 mcg/mL
10 mg2 mL5,000 mcg/mL
10 mg5 mL2,000 mcg/mL

Troubleshooting

Dissolution

Powder not dissolving

Let the vial rest, then swirl gently again. If your BW was refrigerated, allow it to reach room temperature first.

Don't add extra water to force it to dissolve.

Appearance

Cloudy solution after reconstitution

Likely causes are the wrong solvent, contamination, or a compromised water source.

Discard the solution and start again.

Storage

Precipitate forming after reconstitution

Usually caused by storage above 8°C, use beyond 28 days, freeze–thaw cycles, or exposure to light.

Discard the solution.

Post-Reconstitution Storage

2–8°CStore refrigerated
28 daysUse within
No lightProtect from light
No freezingReconstituted solution
  • Store the reconstituted vial at 2–8°C.
  • Use within 28 days of reconstitution.
  • Keep it protected from light.
  • Do not freeze the reconstituted solution — only the dry lyophilised powder can be frozen.
  • Label the vial straight away with the name, lot number, date and concentration.

Laboratory reference only

This guide is for laboratory reference only. All products supplied by Pure Grade Labs are research chemicals and are not for human consumption or therapeutic use. Nothing here is medical advice or dosing guidance. Researchers are responsible for complying with the regulations in their own jurisdiction.